DSCF3233.MP4 Atmel AT89C2051 LPT programmer and LED blinking test hello world of AT89C2051 forgot to upload when project was done last year, make up for proper. Atmel Flash micro programmer. The AT89C2051 is the smallest 8051 member with full resources (128 Byte RAM, 2 Timer, UART). Only the Flash size and pin.

Motivation Being young and stupid I bought a microcontroller without checking for programmer and programming software availability. Fortunately, the programming protocol is simple, and I was able to make my own programmer based on an Arduino. Features • Flashes IntelHex files • Verifies uploads • Erases flash • Dumps flash from chip to a file • Verifies chip ID • Works on Linux • Probably usable on Windows • Requires only a small software modification to allow for AT89C4051 programming Guide A more detailed guide to using this programmer can be found in.

The Atmel AT89C2051 is a low cost microcontroller in a 20-pin DIL package. It runs MCS-51 (commonly termed ‘8051’) code. It works from 2.7V to 6V at anything from 0 Hz up to 24 MHz. It has 2K bytes of Flash memory to hold the program and 128 bytes of RAM.

It has 15 I/O lines, a UART, an analogue comparator and two 16-bit timer/counters. Beadtool 4 crack download. I came across the chip as it’s often used in cheap 7-segment clock kits such as this one from I wanted to reprogram the chip so I could use the kit as a stopwatch/timer instead of a regular clock. Of course I could have bought a programmer to do the job, but reading the chip’s data sheet it seemed straightforward to do the programming with an Arduino – and I thought it would be a fun project to do that.

The chip is programmed a byte at a time by setting up each byte on 8 of the chip’s I/O lines and then pulsing some of the other I/O lines to ‘burn’ the byte to flash memory and move on to the next byte to be programmed. You can also read the existing program out of a chip (unless a read-protect bit has been set) and there are special ways of pulsing the I/O lines to erase the whole chip and so on. The only tricky thing is that one pin has to be raised from the nominal operating voltage of five volts up to twelve volts during programming – the challenge was working out the easiest way to do this using an Arduino.

So I decided to use an Arduino Mega 2560 for this project. A Uno doesn’t have quite enough I/O to do the job properly, and the Mega 2560’s double row of I/O pins makes routing the connections to the chip simple as the chip can sit directly over the double-row connector.

I decided to use a charge pump (voltage multiplier) running off the Arduino’s five volts to generate the programming voltage – that seemed cleaner than needing a separate twelve volt supply. It just uses a few diodes and capacitors and relies on the Arduino pulsing some of its I/O lines to drive the voltage multiplier. A couple of zener diodes clip the voltage down to exactly 5V or 12V and a couple of transistors, also switched by the Arduino, select between either of those voltages or 0V to drive the pin on the chip. I designed a PCB using the free KiCad package. Of the circuit diagram, and here is what KiCad produces as a picture of the design. In the picture it looks like the chip to be programmed is soldered straight into the board, but of course in reality a ZIF socket is fitted in that position so that the chip(s) you are programming can be quickly swapped.

That picture wrongly shows the tracks on the top of the board – I design them that way for home production as the transfer process mirror-images the tracks so that they’re correct for the back of the board. If you fancy making one of your own, it would be quite straightforward to do it on strip board – like I say most of the pins of the chip just connect direct to the Arduino pins that the chip sits over. If you want to etch your own PCB,. Here are a couple of snaps of the prototype board. You can see I didn’t bother to crop back the board edges!