Software Application Disclaimer This page is not a piece of advice to uninstall Zetasizer Software 6.20 by Malvern Instruments from your PC, nor are we saying that Zetasizer Software 6.20 by Malvern Instruments is not a good software application. This page only contains detailed info on how to uninstall Zetasizer Software 6.20 in case you want to.

Instrumat has recorded screenshots of the Malvern Zetasizer DTS software (Vers. 7.01) to show how.

The information above contains registry and disk entries that Advanced Uninstaller PRO stumbled upon and classified as 'leftovers' on other users' computers.

• ZETASIZER APS PARTICLE SIZE BASIC GUIDE MOLECULAR SIZE. • Zetasizer APS Basic Guide MAN0494 Issue 1.0 July 2013 English. • United Kingdom. Tel + [44] (0)1684-892456 Fax + [44] (0)1684-892789 Zetasizer, Malvern and the 'hills' logo are registered trademarks in the UK and/or other countries, and are owned by Malvern Instruments Ltd. Windows is a registered trademark of Microsoft Corporation. • T able of contents Introduction to this manual. 1-1 Introduction.

With the instrument AC plug removed from AC source, connect an electrical jumper across the two AC plug prongs. Keep wires away from high voltage or high temperature parts. Place the AC switch in the on position, connect one lead of ohm-meter to the AC plug prongs tied together and touch other ohm-meter lead in turn to each exposed metallic parts such as antenna terminals, phone jacks, etc. Servisnij rezhim shassi mc 049b. Due to high vacuum and large surface area of picture tube, extreme care should be used in.

• Table of Contents Zetasizer APS Basic Guide Maintenance. 5-1 Introduction. • Measurement types Zetasizer APS APS2000 Particle size Zetasizer APS + APS5000 Particle size PTC-1000 Note For the Zetasizer serial number double-click the APS icon in the status bar. Using this manual Read the Health and Safety information in Chapter 3 before using the instrument. • Where to get help Help desk Direct all queries regarding the system to the local Malvern representative initially. Please quote the following information: Model and serial number of the instrument (located on the rear panel).

• Introduction to this manual Chapter 1 Contact the United Kingdom help desk if the local Malvern representative is not available. The direct line to the United Kingdom Helpdesk is +44 (0) 1684 891800. This help line is primarily English speaking.

• Chapter 1 Introduction to this manual Page 1-4 MAN 0494. • Site requirements Introduction This document outlines site requirements for a Zetasizer APS. Ensure all these are met before the instrument is delivered. Environmental conditions The site must be: Indoors and away from strong light (windows).  Away from heat sources like radiators. • Chapter 2 Site requirements Space required Provide enough space to allow easy access to all components and connections.

This diagram shows the recommended space for a system. Always place the (optional) PTC-1000 to the left of the instrument as the heat output is from the left side of the PTC-1000 and this will prevent hot air being directed towards the APS. • Power cord set requirements Power cord sets must meet the requirements of the country where the product is used. For more information, contact a Malvern representative. General requirements The following requirements apply to all countries: The power cord must be approved by an acceptable accredited agency respon- .

• As with any software, running other applications at the same time may affect the speed of the Zetasizer software. Minimum recommended specification Contact the Malvern Helpdesk or website for the recommended computer specifi- cation, otherwise consult the Software update notification document supplied on the software CD. • Zetasizer APS instruments are Class 1 laser products and as such, require no special laser safety considerations during normal operation. However, during servicing (which must be performed by a qualified Malvern representative), the servicing engineer may be exposed to class 3b or above laser radiation. Adr player dlya videoregistratora windows 7.

We therefore recom- mend that the administrative controls recommendations of the Laser Safety Regu- lations (IEC 60825-1(1993) +A1(1997)+A2(2001) are implemented. • Chapter 2 Site requirements Page 2-6 MAN 0494. • Read and fully understand this section before operating the system. Use of the system in a manner not specified by Malvern Instruments Ltd may impair the protection provided by the system.

The instrument must only be stored or operated in environmental conditions con- forming to Chapter 2. • Electrical warnings and Safety regulations Warning! The Zetasizer APS contains high voltage components. Only Malvern trained personnel are permitted to remove its main cover. The instrument is mains powered and all power cables and electrical sockets should be treated accordingly. Do not place cables where they may become wet.